<?xml version="1.0"?>
<feed xmlns="http://www.w3.org/2005/Atom" xml:lang="en">
		<id>https://wiki.229th.org/index.php?action=history&amp;feed=atom&amp;title=BW_Hover_power_check</id>
		<title>BW Hover power check - Revision history</title>
		<link rel="self" type="application/atom+xml" href="https://wiki.229th.org/index.php?action=history&amp;feed=atom&amp;title=BW_Hover_power_check"/>
		<link rel="alternate" type="text/html" href="https://wiki.229th.org/index.php?title=BW_Hover_power_check&amp;action=history"/>
		<updated>2026-08-14T08:39:47Z</updated>
		<subtitle>Revision history for this page on the wiki</subtitle>
		<generator>MediaWiki 1.27.7</generator>

	<entry>
		<id>https://wiki.229th.org/index.php?title=BW_Hover_power_check&amp;diff=220&amp;oldid=prev</id>
		<title>WikiSysop: Created page with &quot;File:229AHB_logo.png  '''Basic Wings requirement:''' TASK 1028 - ''PERFORM HOVER POWER CHECK''    ==3. Basic Wings – Hover power check==  ===3.1. Objective: Perform...&quot;</title>
		<link rel="alternate" type="text/html" href="https://wiki.229th.org/index.php?title=BW_Hover_power_check&amp;diff=220&amp;oldid=prev"/>
				<updated>2020-02-20T07:27:30Z</updated>
		
		<summary type="html">&lt;p&gt;Created page with &amp;quot;&lt;a href=&quot;/index.php?title=File:229AHB_logo.png&quot; title=&quot;File:229AHB logo.png&quot;&gt;File:229AHB_logo.png&lt;/a&gt;  &amp;#039;&amp;#039;&amp;#039;Basic Wings requirement:&amp;#039;&amp;#039;&amp;#039; &lt;a href=&quot;/index.php?title=TASK_1028&quot; title=&quot;TASK 1028&quot;&gt;TASK 1028&lt;/a&gt; - &amp;#039;&amp;#039;PERFORM HOVER POWER CHECK&amp;#039;&amp;#039;    ==3. Basic Wings – Hover power check==  ===3.1. Objective: Perform...&amp;quot;&lt;/p&gt;
&lt;p&gt;&lt;b&gt;New page&lt;/b&gt;&lt;/p&gt;&lt;div&gt;[[File:229AHB_logo.png]]&lt;br /&gt;
&lt;br /&gt;
'''Basic Wings requirement:''' [[TASK 1028]] - ''PERFORM HOVER POWER CHECK''&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
==3. Basic Wings – Hover power check==&lt;br /&gt;
&lt;br /&gt;
===3.1. Objective: Perform a hover power check as per 1028 UH-1h ATM 2007.===&lt;br /&gt;
&lt;br /&gt;
===3.2. Competencies expected: The pilot will demonstrate bringing his craft to a 5’ stationary hover.===&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
CONDITIONS: In a UH-1 helicopter at an appropriate hover height and with performance planning information available.&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
STANDARDS:      &amp;quot;Mission Readiness&amp;quot;   &lt;br /&gt;
&lt;br /&gt;
1.  Determine if sufficient power is available to perform the mission.      GO/NO-GO     IGE vs OGE&lt;br /&gt;
&lt;br /&gt;
2.  Determine if wind condition exceeds directional control margin (DCM) or longitudinal cyclic values.&lt;br /&gt;
&lt;br /&gt;
3.  Determine Approach based on center of gravity (COG) limits, if applicable (using indicated fuel).   Hover vs Running Landing&lt;br /&gt;
               &lt;br /&gt;
&lt;br /&gt;
PROCEDURES:&lt;br /&gt;
&lt;br /&gt;
Use a 5-foot stationary hover  (2-foot stationary hover when using tabular data)&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
Any time the load or environmental conditions change significantly (200 pound increase,  500 feet PA increase, or ± 5 degrees Celsius), &lt;br /&gt;
&lt;br /&gt;
perform additional hover power checks and,if necessary, recompute the PPC using tabular data.   (See Task 1011.)&lt;br /&gt;
                    &lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
If the torque required to maintain a stationary hover does not exceed the OGE Go/No-Go torque, any maneuver requiring OGE/IGE power or less may be attempted.&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
If the torque required to maintain a stationary hover exceeds  the  OGE Go/No-Go torque  but does not exceed the IGE Go/No-Go, only IGE maneuvers may be attempted.&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
If the IGE NO-GO torque value is indicated prior to reaching hover height, stop the hover power check and land the aircraft.&lt;/div&gt;</summary>
		<author><name>WikiSysop</name></author>	</entry>

	</feed>